Products

Contact Us

GN Solids America LLC

GN Solids Control Brochure Download GN Brochure

Tel:+1-713-8780880

Email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Add:6710 Windfern Road, Houston, TX 77040,USA

 

Vertical Cuttings Dryer

vertical-cuttings-dryer1
vertical-cuttings-dryer2
GN Vertical Cuttings Dryer is used in the drilling industry for recovery oil from the drilling cuttings.In drilling operations, typical solids control equipment discards 1-4 barrels of liquid for each barrel of solids removed.
  • Description

    GN Vertical Cuttings Dryer is used in the drilling industry for recovery oil from the drilling cuttings.In drilling operations, typical solids control equipment discards 1-4 barrels of liquid for each barrel of solids removed.GN drilling cuttings dryer system consisting of Vertical cuttings Dryer and the relevant equipment could discharge 1 barrel of liquid for 4 barrels of solids removed.GNCD930 vertical cuttings dryer has proven to reduce this liquid to below 5% (OOC) by weight by site test:

    • Reduce the amount of OBM or SBM on cuttings discharge to reduce waste volume and meet environmental objectives.
    • Recover valuable base fluids for reuse and lower the cost.
    • Reduce fluid content prior to other treatment, thereby increasing process capacity.

    In short, GNCD930 Vertical Cuttings Dryer could help you meet environmental objectives by reducing waste volume, maximizing liquid recovery and reducing your project cost.GN Solids Control can provide all-around mud recycling and treatment equipment.

    Features and Benefits for GN Vertical Cuttings Dryer

    • The flights are made from hard high chrome alloy material to be anti-abrasive from solids and ensure long operational life vertical cuttings dryer.
    • Air Knife is Provided for cleaning the screen to avoid screen blinding.
    • Balance testing for all major rotary components to minimize vibration & noisy
    • Individual oil lubrication system with automatic alarm for pressure limit.
    • Screw conveyor installed under the dryer to pick up the dry solids for continues operation.
    • Cleaning pump provided for avoiding solids accumulation in the cuttings dryer

    GNCD930 cuttings dryer is a single stage continuous phase vertical screen centrifuge that has proven to reduce the oil on cuttings to as low as 5% by dry weight and typically achieves below 5% OOC levels. GNCD930 Vertical cuttings dryer is capable of processing over 40-50 tons per hour and can deliver dry solids under the most severe loading. GNCD930Cuttings Dryer has been used on many types of fluids, including drilling fluids of both synthetic and oil based mud. As with all solid control equipment, like shakers, centrifuges and cyclone separator, viscosity will have an impact on performance. Viscosity is determined by many factors including solids content, solids size, fluid type and fluid temperature.

    In drilling operations, typical solids control equipment discards 1-4 barrels of liquid for each barrel of solids removed.GN drilling cuttings dryer system could discharge 1 barrel of liquid for 4 barrels of solids removed. This recovery is measured after processing through the solid bowl decanting centrifuge.
    The drilling fluid from vertical cuttings dryer contains a percentage of low gravity fine solids that should be treated by a high speed centrifuge before the mud can be returned to the active system. This may not be necessary in all conditions. The cuttings dryer screen bowl is available with different mesh openings.
    Other than the vertical cuttings dryer itself, other equipment could include a support stand and a high-speed centrifuge with feed pump and stand. Additional equipment may include the feed system, whether auger, vacuum transfer system, or positive displacement feed pump package.

    Installation time varies greatly with conditions and is dependent on many things, most importantly a proper survey prior to installation. Installation time is achievable within 2 or 3 days if no hot work is needed.

    Vertical Cuttings Dryer Parameter

    Model GNCD730A GNCD730A-VFD GNCD930D GNCD930D-VFD
    Capacity  20-40 Tons/H 30~50 Tons/H
    Drying Efficiency  OOC ≤ 5%
    Screen Max Diameter  730mm 930mm
    Screen Opening  0.25/0.35/0.5mm
    Rotation Speed  1200/1500RPM 0-1200RPM/0-1500RPM 900RPM/1200RPM 0~900RPM/0-1200RPM
    G Force 588 or  918 G 420 or 750 G
    Oil Tank Capacity  48L 48L
     Air Knife Input Pressure 0.69Mpa 0.69Mpa
     Air Knife Input Capacity  1.4m³/m 1.8m³/m
    Flushing Pump Qty  1pcs
    Main Motor  37Kw 55Kw (75HP)
    Oil Pump  0.55Kw(0.75HP) 0.55Kw(0.75HP)
    Flushing Pump Power  4Kw(5.5HP) 4Kw(5.5HP)
    Ex Standard  ExdIIBt4 / IEC EX/ ATEX
    Electric Cabinet  Exd Positive Pressurized Exd Positive Pressurized
    Weight  3200Kg 3016Kg 4600Kg 4400Kg
    Dimension  2265x1518x1310mm 2640×1810×1650mm

    Vertical Cuttings Dryer Videos

  • YOUR CONTENT CODE FOR REVIEWS/COMMENTS GOES HERE
  • YOUR CONTENT CODE FOR RELATED PRODUCTS GOES HERE

Contact Us

Fields marked with ( * ) are required.

 
×

Contact us

By submitting this form, you accept our privacy policy.
×

Login

  or   Create an account

Forgot your password? |  Forgot your username?

×

WS Register



  or   Login
×

Subscribe to Our Newsletter

×